MC6Pro Din 5 Midi in through to TRS 3.5mm setting lost when powering off

Hello

I am experiencing a particular issue. When I turn off my MC6Pro I am losing only 1 setting in my programming. The Din 5 Midi in through to TRS 3.5mm setting keeps reverting to unchecked. I noticed my midi through commands via TRS 3.5mm arnt working on my pedal board so I double check my settings connecting the MC6Pro to my laptop. I checked it with both versions of the editor. The offline and desktop editor show that the midi through 3.5mm option is unchecked. This started happening recently and has not been an issue until the past few weeks. When I checked the Din 5 Midi in through to TRS 3.5mm the editor prompts me to save the setting and reboot. The option is now active but will not retain it when I turn it off. The first time I noticed the problem it was a few weeks ago and then it didn’t happen again for a few days. As of now I rechecked the box on Friday, turned the unit off. Powered it on on Saturday and it worked. I turned it off and powered it back on Sunday and the setting was lost. The only setting that is being erased is the Din 5 Midi in through to TRS 3.5mm. All of my other settings are not erased.

Card created

This is an automatically generated message

A Trello card has been created for this request: MC6Pro Din 5 Midi in through to TRS 3.5mm setting lost when powering off

Here’s a picture of my setup. The midi 5 pin out from the Quad Cortex goes to the midi 5 pin in of the mc6 pro. The midi 5-pin out of the mc6 pro goes into the source audio encounter midi in 5 pin. The 5 pin out of the encounter goes back into the end of the Quad Cortex. The mc6 pro TRS 3.5 mm midi out is going into my midi solo stereo Loop Switcher 5 pin in.

I havent had any luck getting a reply. Please help.

Hi!

Can you let me know the firmware version your MC6 PRO is running?
iirc this was a bug in an earlier firmware but is fixed in the latest v3.13.6 firmware.

Firmware

v3.14.0.260821500

I wasn’t able to replicate this.

Can you troubleshoot these steps:

  1. Select DIN5 MIDI IN Thru to 3.5mm
  2. Click on Save settings, but do not restart the controller (click on restart later)
  3. Click on Reset to default (the MIDI Thru matrix settings should be all unchecked)
  4. Click on Load Settings.

Does the correct settings get loaded?

I’ll try this out later today. In theory I should also be able to midi though into the 5pin Din on the MC6Pro and midi out through an Omniport right? This will allow any midi messages coming from the Quad cortex going through the MC6Pro and also any midi messages coming from the MC6Pro to command the midi stereo loop right? Basically I should have all of the capabilities I have connecting to the omniports instead of the 3.5mm out? The omniport would only be sending midi messages.

I did everything you asked and yes. When I hit reset to default everything was cleared out and then when I hit load settings all of my preset information was reloaded including my Din 5 midi through 3.5 mm. I then proceeded to save the settings and do a restart. The setting was retained . I turned the unit off by turning off the power on my pedal board and when I turned it back on the Din 5 midi in through to 3.5 mm setting is off. It’s the only setting that is not being retained. At this point I followed your instructions above and the outcome was different. This time when I hit the reset to default, then load settings my settings loaded but it did not check the 3.5 mm setting.

I did configure my omniports so that I can send my midi through commands through my omniport to the stereo switcher. So I’m basically performing the same functions I was performing before through the 3.5 mm output but through the omniport number four. I have seen the settings and create a backups and turned off the unit. I’ll test it again tomorrow to see if it retained the settings.

I spent the last couple of days testing the 3.5 mm midi out and the 1/4 inch omniport. Both are configured to MIDI through to the same device. With the omniport settings saved I could turn off the MC6Pro and reboot without losing my Omniport programming. With the 3.5 mm midi out I lose programming every single time I reboot. Though I found a workaround by using the omniport instead of the 3.5 mm midi out , I guess we need to understand if this is a software glitch or If my mc6 Pro has a issue that needs warrantied.

So when you save your midi thru matrix settings as such:

And then restart your MC6 PRO, only the Omniport checkbox will be selected, but the 3.5mm will be unchecked?

Just want to confirm that the editor you are using is the same version as well?

If the issue persists, please drop us an email with your order details and a link to this thread.

I apologize for the delay. We are both using the same editor and firmware version. This is very interesting. Before I was checking only one option at a time, not together. I either had the 3.5mm option checked which would loose its programing once the MC6Pro was turned off or only the the Omniport option checked which would not loose its programming. I am now testing both the 3.5mm and the Omniport options just like in your picture. With both options checked I’m very surprised but I’m not loosing the 3.5mm option when rebooting. I will continue testing with both the 3.5mm and Ominports active throughout the weekend and will report back. Though I have both Omniport and 3.5mm checked on the editor I physically am only using the 3.5mm hooked up to my midi device.

I tested out having both the omniport and the 3.5 mm through options checked at the same time. Having both of these options checked makes it where the 3.5 mm option does not uncheck when I reboot the mc6 pro. There must be a glitch in the editor where the 3.5 mm box has to be checked in conjunction with another option otherwise it won’t retain the setting.

thanks for the feedback. I looked through the code again and can’t find any issues. I made some changes to the editor and have pushed the updates to the beta editor (editor-beta.morningstar.io). If possible, can you try it there and let me know if the same issue persists for you?

Hello. I am traveling but will test it out this weekend.